Rainfall was 213 mm, 46% below the baseline mean while average temperature ran 0.7 °C above baseline mean

213mm rain
−46% against the 1991–2020 normal
Normal for this window: 395 mm. Baseline range 231–649 mm.
1,560°C·day
+7.7% heat against normal
Normal: 1,449 °C·day (single sine). Mean temperature +0.7 °C against normal.
−163mm
Rain minus crop water need
213 mm rain against 377 mm estimated ETc (climatic balance, not soil moisture).
Complete core data on 138 of 138 daysNASA POWER · MERRA-2 grid ~0.5°, not a stationBaseline 1991–2020 (30 seasons)
Chapter 1 · Warmth

Temperature and accumulated heat

Why it matters

Temperature sets the pace of crop development and the balance between growth and respiration. The daily extremes show the range plants lived through; growing degree-days add up the heat available for development, the thermal time agronomists use to follow a crop through its season. Heat is counted above the Maize base of 10 °C.

Temperature and accumulated heat chart

How to read it. Top panel: daily maximum (orange) and minimum (blue) air temperature. Bottom panel: growing degree-days, the heat above 10 °C (Maize base) added up day by day. Grey bands show 1991–2020: the normal daily range on top, and the middle half of baseline years below, with the median year as a dashed line. A season line above its band ran warmer than usual.

Temperatures ran +0.7 °C against normal; heat accumulated 7.7% above normal

AId Summary. Mean temperature of 20.6 °C exceeds the 1991–2020 mean of 19.9 °C, indicating a warmer season. Accumulated heat above the maize base reached 1,464 °C·day, surpassing the normal accumulation, so thermal time progressed faster. The excess heat suggests that maize development could advance relative to a typical season, prompting the agronomist to verify whether crop phenology aligns with expected dates.

Chapter 2 · Water

Rain and water demand

Why it matters

Rain is the supply side of the crop water budget and evapotranspiration the demand side. Following both through the season shows when a surplus or a shortfall built up and how early it began, which is when a rainfed crop is most exposed.

Rain and water demand chart

How to read it. Both lines add up from the first day of the period. The blue line is cumulative rain; the orange line is cumulative estimated crop water need (ETc), the reference demand scaled by the crop's coefficient for each stage. Blue shading marks stretches where rain was ahead of demand, orange shading where demand was ahead. The dashed line is the cumulative rain of the median season in 1991–2020.

Rain kept up with crop water need until 22 Apr, then fell behind and covered 57% of it
Estimated crop water need was 377 mm against 213 mm of rain (−163 mm).
Against normal: 213 mm versus a 395 mm mean; lower than every baseline season (driest baseline season 231 mm).
Dry spells. The longest dry run was 15 days (the typical season's longest is 24 days), so rain came in small amounts rather than long gaps.

AId Summary. Maize crop water need for the period was 376.6 mm, while precipitation was only 213.3 mm, producing a climatic balance of −163.3 mm that indicates atmospheric demand surpassed supply. The longest consecutive dry period lasted 15 days, reinforcing that rainfall was spread over short spells rather than sustained. These conditions suggest that the crop would require supplemental irrigation to meet its evapotranspiration demand.

Chapter 3 · Atmospheric demand

Atmospheric drying demand (VPD)

Why it matters

Vapour pressure deficit (VPD) measures how strongly dry air draws water from leaves and soil. High VPD speeds transpiration and pushes plants to close their stomata, which also limits carbon uptake: it is the atmospheric side of water stress.

Atmospheric drying demand (VPD) chart

How to read it. The violet line is each day's estimated peak-demand VPD, in kilopascals (kPa). The dashed line marks 2 kPa, a generic reference level; amber shading shows how far demand rose above it.

Peak-demand VPD passed 2 kPa on 47 of 138 days

AId Summary. Peak‑demand VPD reached 2.88 kPa, well above the generic 2 kPa reference, and 47 of 138 days exceeded that threshold, indicating sustained high transpiration demand. The average 24‑hour VPD of 0.64 kPa suggests that most of the period was relatively moist, but repeated excursions above 2 kPa could prompt stomatal closure and elevate hydraulic risk when soil moisture is limited. These conditions may limit carbon uptake in maize, which is already sensitive to high temperatures.

Chapter 4 · Stress events

Stress-event calendar

Why it matters

Seasonal totals can hide timing. This calendar marks every day on which a stress condition occurred, so clusters of heat, dry spells or cool nights can be lined up with the crop's sensitive stages. For Maize, the crop registry lists flowering/silking, grain filling as the stages most sensitive to heat and water.

Stress-event calendar chart

How to read it. Each row is one condition and each column one day; an orange cell means the condition occurred that day. A dry spell is a run of at least 7 days with under 1 mm of rain.

5 dry spells of a week or more; no day at or above 35 °C, 12 cool nights
Heat: 0 days at or above 35 °C; hottest day 32.1 °C.
Cold: coldest night 3.2 °C; 0 frost days; 12 nights at or below 10 °C.

AId Summary. Peak‑demand VPD occurred on 47 days, indicating sustained high evaporative demand. Five dry spells added low precipitation, compounding the VPD pressure. Twelve nights fell at or below the maize base temperature, reflecting cooler periods that could reduce transpiration. The combination of high VPD days and extended dry spells suggests that the crop experienced periods of elevated atmospheric demand during the season.

Appendix

Crop context — Maize

CropMaize
Cultivarunknown
Planting date20220218
Harvest/evaluation date20220705
Irrigationrainfed

Thermal time accumulates from the planting date and stopping at the harvest date (20220705) using the sourced base 10 °C (medium confidence), upper cutoff 30 °C. Accumulated: 1,464 °C·day. It is a thermal-time indicator, not a phenological stage.

Solar radiation

Why it matters

Incoming solar radiation is the energy behind photosynthesis and evaporation. Cloudy spells lower both the potential for growth and the drying power of the air.

Solar radiation chart

How to read it. The line is the daily all-sky shortwave radiation reaching the surface, in MJ/m² per day.

AId Summary. Mean solar radiation 17.32 MJ m⁻² day⁻¹ provides energy for photosynthesis and drives evapotranspiration. For maize, developmental rates are governed between 10.0 °C and 30.0 °C; thus, the radiation is available when temperatures fall within this window, allowing the crop to translate light into growth. The mean radiation likely increases evaporative demand, suggesting that irrigation scheduling should be checked to meet the elevated water requirement.

Wind speed

Why it matters

Wind renews the air around leaves, so it raises evaporation and transpiration and enters the reference evapotranspiration calculation. Strong wind also matters for spraying and for mechanical damage.

Wind speed chart

How to read it. The solid line is the daily mean wind speed at 10 m, in m/s.

AId Summary. Wind speed of 2.57 m s⁻¹ at 10 m height represents moderate aerodynamic resistance, which elevates evaporative demand for maize by enhancing the aerodynamic term in ET₀ calculations. This sustained wind can raise transpiration demand, especially when temperatures approach the crop's upper threshold of 30 °C. Managers should consider that such wind conditions may require adjustments to irrigation timing to meet the increased water demand.

Wind direction and speed

Why it matters

The prevailing wind direction matters for windbreak placement, spray drift and the exposure of field edges.

Wind direction and speed chart

How to read it. Each spoke is a compass direction the wind came from; its length is the share of days, split into speed classes from light (pale) to strong (dark).

AId Summary. Strongest winds on the day came from the southeast, consistent with the persistent SE dominance. The mean 10‑m wind speed of 2.57 m/s provides moderate air movement, while a peak of 4.94 m/s suggests occasional higher flow that could enhance evaporative demand. These conditions support routine transpiration but are below the threshold that would raise lodging risk for maize.

Environmental parameters

Temperature at 2 Meters T2M · °C Average Air Temperature at 2 m (°C): Modeled daily average air temperature. Data is obtained from the NASA MERRA-2 assimilation model (1981-Present, ~0.5°x0.625° resolution). In agriculture, T2M is critical for calculating Growing Degree Days (GDD) and modeling crop developmental stages and growth rates. Used in machine learning models for yield prediction and thermal stress assessment. NASA POWER via aidweather Corrected Total Precipitation PRECTOTCORR · mm/day Corrected Total Precipitation (mm/day): Total liquid and frozen water precipitation, adjusted for known biases. Data is obtained from the NASA MERRA-2 model (1981/1997-Present, ~0.5°x0.625° resolution). Essential for water balance models, irrigation scheduling, and assessing drought/flood risk. It's a primary input feature for deep learning models predicting crop yield. NASA POWER via aidweather Mean vapor pressure deficit VPD_MEAN · kPa Daily drying power of the air: saturation vapour pressure at the mean air temperature minus the actual vapour pressure (FAO-56). Higher values mean the atmosphere pulls water from leaves and soil faster. Derived in AidWeather Report Peak-demand vapor pressure deficit VPD_MAX · kPa Estimated drying power of the air at the day's maximum temperature: saturation vapour pressure at the daily maximum minus the day's mean actual vapour pressure (FAO-56). It approximates the strongest demand of the day. Derived in AidWeather Report Relative Humidity at 2 Meters RH2M · % Relative Humidity at 2 m (%): Ratio of actual water vapor content to the maximum possible saturation. Data is obtained from the NASA MERRA-2 model (1981-Present, ~0.5°x0.625° resolution). RH2M affects transpiration rates (low RH increases water loss) and disease incidence. Used in ML models for predicting irrigation needs and disease risk. NASA POWER via aidweather Wind Speed at 10 Meters WS10M · m/s Average Wind Speed at 10 m (m/s): Modeled daily average horizontal movement of air. Data is obtained from the NASA MERRA-2 model (1981-Present). Wind is a crucial factor in the Evapotranspiration (ET) calculation and can cause mechanical stress. Used in predictive models for water loss and general crop stress. NASA POWER via aidweather All Sky Surface Shortwave Downward Irradiance ALLSKY_SFC_SW_DWN · MJ/m²/day All Sky Surface Shortwave Downward Radiation (MJ/m²/day): Total solar energy reaching the surface under actual atmospheric conditions (Direct + Diffuse). Data is derived from NASA satellite observations (1984-Present, ~1.0°x1.0° resolution). This is the key energy input for calculating Reference Evapotranspiration (ETo) using methods like Penman-Monteith, which drives irrigation decisions. NASA POWER via aidweather All Sky Surface PAR Total ALLSKY_SFC_PAR_TOT · MJ/m²/day All Sky Photosynthetically Active Radiation (MJ/m²/day): The total energy flux (400-700 nm) used by plants for photosynthesis. Data is derived from NASA satellite observations (1984-Present, ~1.0°x1.0° resolution). This directly quantifies the light available for plant growth. Used in Crop Growth Models (CGMs) like DSSAT and APSIM to simulate biomass accumulation and final yield. NASA POWER via aidweather Growing degree days GDD · °C-day Estimated daily thermal time above the selected base temperature; the default method integrates modeled hourly T2M with an optional upper threshold. Derived in AidWeather Report Reference evapotranspiration ET0 · mm/day Water a well-watered reference grass surface would lose to the air each day, computed with the FAO-56 Penman–Monteith equation from temperature, humidity, wind and solar radiation. It measures atmospheric water demand, not what a crop used. Derived in AidWeather Report

Notes

Warmth · Temperature and accumulated heat

  • Growing degree-days use a 10 °C base and 30 °C cutoff; the report's method is hourly[3].
  • The baseline comparison recomputes heat with the single-sine method for the season and every baseline year[4], so the two are comparable whichever method the report uses.
  • The report's own hourly method gives 1,464 °C·day for the same season (the exported CUM_GDD).
  • Thermal time measures heat available for development; it does not by itself establish crop stage or harvest timing.
  • NASA POWER temperatures describe a ~0.5° grid cell and smooth local extremes[1].

Water · Rain and water demand

  • Dry day = under 1 mm; dry spell = at least 7 consecutive dry days[6].
  • ET0 is FAO-56 Penman–Monteith[2]; ETc = Kc × ET0 with the staged single-Kc curve[5]. FAO-56 staged single Kc: 0.30 → 1.20 → 0.60; default stage lengths scaled to supplied planting–harvest window; initial 22.08 days, development 38.64 days, mid 44.16 days, late 33.12 days. FAO-56 Table 11, maize grain, Nigeria humid, June; indicative timing only, scaled to supplied planting–harvest window, not local calibration. FAO-56 Table 12, field maize (grain), Kc end 0.60 for harvest at high grain moisture.
  • Rain minus crop water need is a climatic balance, not soil moisture: it excludes soil storage, runoff, drainage, irrigation and rooting depth.
  • The normal-rain line is the median of 30 seasons (1991–2020) for the same window.
  • NASA POWER rainfall is a grid-cell estimate and can miss local showers; an on-farm rain gauge is the better record for a single field.

Atmospheric demand · Atmospheric drying demand (VPD)

  • Peak-demand VPD pairs saturation vapour pressure at the daily maximum temperature with the day's mean vapour pressure, so it estimates the strongest demand of the day rather than measuring afternoon VPD[2].
  • The 2 kPa line is a generic reference, not a crop threshold: the VPD at which stomata close is species-specific[7].
  • VPD describes the atmosphere; it is not a measurement of plant water status or soil water.

Stress events · Stress-event calendar

  • Event definitions follow the ETCCDI climate-extreme indices where one exists (dry days, consecutive dry days, maximum and minimum temperature)[6].
  • 35 °C is a generic heat reference, not crop-specific.
  • The cool-night threshold is the Maize base (10 °C).
  • A near-freezing minimum does not by itself establish canopy-level frost, and a hot day does not by itself establish heat injury.

Appendix · Solar radiation

  • Radiation is the all-sky value for the grid cell; it does not by itself establish photosynthetic performance.

Appendix · Wind speed

  • Daily mean wind at 10 m is not a gust and does not by itself establish lodging risk; the reference evapotranspiration converts it to 2 m (FAO-56 Eq. 47).

Appendix · Wind direction and speed

  • Days with a missing speed, or a direction missing or outside 0–360°, are left out of the counts, so the percentages sum to 100.

Crop context

  • Missing crop information is unknown, not assumed. Cultivar, irrigation system, soil type, phenological stage and management are not inferred beyond what was supplied.

Reading this report

  • Compare these values with an on-farm rain gauge: a ~0.5° grid cell can miss local showers.
  • Soil water, crop stage and management are unknown to this report; it does not say how the crop responded.
  • NASA POWER is a roughly 0.5° gridded product (resolution varies by variable). It smooths local extremes of rainfall and temperature and is not a substitute for a station measurement.
  • Point values represent the surrounding grid cell, not necessarily conditions at the exact coordinates.